repair a hotpointwma30?

could you please help me i have took my hotpoint wma30 apart to repair the bearings and i am left with a large spring and i cant remember where it goes

done

how do i fix the banging noise that sounds like a ballbearing in the machin?

i have a hotpoint first edition washing machine 1000rpm. i have just had the bearing replaced, but the engineer said that the pulled was worn, and it is making a banging noise that sounds like there ... more

done

How can i fix Hotpoint Aquarius electric shower that just dribbles?

We have just moved in to an oldish house and installed a new bathroom. The old bathroom had a new-looking Hotpoint Aquarius electric shower installed, so we re-used that. The builder fitted it but it ... more

done

How can we fix our hotpoint wd860 washer dryer?

My brand new hotpoint wd860 washes fine, when it comes to tumble drying, the thermostat keeps cutting out. Its 7 weeks old and weve had one new thermostat and are awaiting another engineer. Any id ... more

done

hotpoint Aquarius 1100 wd61 doesn't spin?

When you've selected to wash it fills the machine with water washing the powder down but nothing happens the selector dial clicks through its program Sequence but the drum doesn't turn and it leaves ... more

done

Hotpoint 9340 Dryer Problem?

I have a fault code E-2 on the above dryer, which is Thermistor or sensing circuit failure. anyone any ideas how to fix this problem or the cost involved/parts required?? thanks for any help.

done

how can i open?

how can i open a hotpoint aquarius washing machine full of water and washing

done

Hotpoint microwave display?

We have a Hotpoint Countersaver plus microwave that is going on three years old. It just started making a sound grinding noise and the display panel is flashing strange symbols. It seems to work ok ... more

done

Can anyone help me fix my Hotpoint WD71?

We have lost our service manual and during mid wash this display appeared "E 30 refer to user guide". Can anyone pls advise what the problem is. Thanx in adavance.

done

Does anyone know how to replace the drum bearings on a hotpoint aquarius wm?

Does anyone know how the drum bearings go back into a hotpoint aquarius 1100 wm63p. I managed to remove them ok but I am having some difficulty getting the new ones back in. In which order do they go ... more

done

Hotpoint wahing machine guide?

I have a Aquarius Wash System Plus (ULTIMO 1400) and although it is about 10 years old it is in really good condition and has just started to play up. It is a digital machine and at present is not wo ... more

done

The belt on my hotpoint 9326 reversing dryer comes off the spindle?

I have replaced the belt on my hotpoint 9326 aquarius reversing tumbledryer and put it between the pulleys onto the motor spindle.Now when it runs the belt runs off the motor spindle.Should there be a ... more

done

how can i fix noisiest washing machine hotpoint aquarius 1100?

when machine spins it makes a horrendous noise, it seems fine on when not spinning but when it does spin it makes an unbelievable noise. has only just started doing this and when the washing comes out ... more

done

why does my hotpoint washer machine keep cutting out?

when the washer is switched on a few seconds after starting it cuts out and blows a fuse

done

How can i fix my Hotpoint Aquarius TDC30 Condenser?

All filters are clean dryer tumbles but no hot air so clothes do not dry

done

how do i remove/replace hotpoint drum bearings on wm62?

how easy/difficult is it to replace bearings on aquarius 1000 wm62 washing machine.any tips as to removal thanks

done

How do I replace a bearing on a Washing machine?

the machine is a hotpoint WM53

done

CODE AL 03 on HOTPOINT DWF70?

How can I get my hands on a DWF70 (Hotpoint Ultima) manual, or does anyone know what the AL 03 fault code is?

done

How can I fix my Hotpoint WM63 washing machine?

Machine stops at beginning of RINSE CYCLE in any programme mode. It can be operated manually by advancing the timer control.

done

Test program?

Help - my hotpoint wahing machine is stuck on test program - how can i get if off this to start using it??

done