Lawnmower not starting?

My mower just quit in the middle of running, and it will not start. It's about 5 or 6 years old, never had any trouble with it, the model is Craftsman 6.0, 21", Briggs Stratton engine

done

Briggs and Stranton 3.5 motor?

I need to know the gap between the coil and fly wheel of my 3.5 hp lawn mower. Model #9D902 Type 2005-82

done

Briggs & Stratton 6.5 Intek Magneto short?

My chipper shredder stopped suddenly while not under load. I tested and found no spark. Then I disconnected the wires from the magneto to the throttle kill switch and measured the resistance from the ... more

done

starter removal?

how do i remove the starter on a briggs and stratton 18.5 twin valve engine? model 303777 type 1032-a1 code 96112111 thanks

Briggs Straton Model 445577 type 0755BI Code 080716YG ?

The boss side of the engine plug is working. The passenger side plug is not working. When I pull the Kill Switch wire on bottom of coil, the passenger side starts working. Why is the Kill Switch W ... more

done

how do i fix my briggs&stratton side shaft engine ?

my older craftsman rototiller with a 5 horsepower briggs&stratton side shaft drive has a bad bearing opposite the flywheel. there is a 6 ballbearing pullstart assemblly with 2 screw holes that hold t ... more

done

Briggs&Stratton mod.311707 type 0132-E1?

oil in the air filter box.Blowing white smoke

done

briggs & stratton #42a707 starter?

do I need to remove flywheel to get the strater off

How do i change the condenser on my lawnmower?

My Briggs and stratton 35 lawn mower will not start, i have taken it to the repair shop and the mechanic said it needs a new condenser which will be £50 to replace. Where can i get a condenser and c ... more

how can I fix myt lawnmower?

I have a 16 hp briggs and stratton engine on a murray mower.. sometimes it will mow my whole yard but, but if I shut it off and it will not restart when hot any suggestions??

done

Briggs and stratton engine?

Harry mower briggs and stratton engine.Runs well but has started"hunting".Checked the carb and problem seems to be with 2 springs fixed to the throttle controls.What are they and what do they do?

valve lash for 16.5 briggs and stratton motor?

I,m interested in the exhaust and intake valve lash adjustment specifications on the 16.5 hp briggs and straton riding mower engine.

Engine Timing?

I would like to know where the timing marks are on the crankshaft and camshaft and fly wheel magnito of the Briggs and Stratton Lawn Mower Model 3.75 Sprint.

done

Craftsman LT 1000 looses power when i engage deck?

I have a 18 hp OHV Briggs & Stratton and after using it for a while i put the parking brake on to empty lawn trimmings and when i go to engage deck it whats to die. As soon as i disengage blades it wi ... more

Is a special tool needed to remove ring retaining on an electric starter?

Briggs & Stratton 19.5 H.P. lawn tractor?

done

How can i fit a clutch to Briggs and straton 5.5HP Vanguard?

I have acquired a b&s HP vanguard ohv engine (type 007801 md115432 code 94022849) that was attached to a generator and i would like to fit this to a go kart for my lad. the end of the crank is tapered ... more

done

Hayter lawnmower problem?

I have a hayter mower fitted with a briggs and stratton quantum xm 35 petrol engine. model 121882 type 0419-01 code 9301085 The engine fires and turns over 4 or 5 times then cuts out also petrol is ... more

done

engine will not fire?

I have a Briggs & Stratton engine, 16.5 HP Model # 28W707-01210-E1. Good compression, gets fuel, has spark but will not fire. It is presently on a test stand not in a tractor. Wiring may be the proble ... more

done

How to fix a Briggs 475 engine that starts when primed but then quits?

My Briggs and Stratton 475 pushmower engine starts up when primed, but then immediately quits, like it isn't getting gas. You can prime it again and it will start back up and then immediately quit ag ... more

done

briggs 12.5 twin 1986?

burning up coils red wire to ignition goes to black on coil is there a plastic washer inbetween burning new coils please reply thank you paul.