what torque specifications on honda outboard?

how much torque do i put on the cylinder head bolts on a 50 horsepower honda outboard engine?

done

1995 Yamaha Waveventure quit running?

I just bought this and took it out for a test run, it hadn't been in the water for over a year, it ran fine for about a 1/2 hour (Top speed 51 MPH) then all of a sudden it lost power, engine quit, re- ... more

done

my 4hp 4stroke mariner keeps cutting out?

my 4hp 4stroke mariner 2005 modle outboard runs fine in the bin but as soon as im out in the sea after 10-30 mins it cuts out as if the feul has run out and the wont start again for a while ,it also s ... more

done

4year old Honda 10hp...starting probs?

I've changed the lower unit oil, and sump oil (btw should the yellow sump checker have a plastic probe on it to show level?).....now it won't start. Ideas?

done

How can I get my 2007 VX110 Deluxe Yamaha Waverunner to run over 34 mph?

I bought it new in June 2007. It ran fine last summer and the first 2 - 3 times I took it out this summer. I took it out a couple of weeks ago and it won't run over 32 - 36 mph. If you know how I c ... more

done

YAMAHA WAVERUNNER 1200XLT WILL NOT START?

HI I HAVE A 2003 LO HOUR WAVERUNNER 12OOXLT WHICH I HAD RUNNING GREAT UNTIL THIS WEEKEND. I TRIED TO START IT AND THE NEW BATTERY SLOWLY TURNED OVER THE MOTOR (WAS OUT OF GAS). I PUT IN NEW GAS, REC ... more

done

2007 VX110 Yamha Waverunner -Why won't it run over 32-36 mph?

I bought it new in June 2007. I ran it in beginner mode the appropriate length of time and it ran fine all summer. After it was stored for the winter and I took it out the first time this summer, it ... more

done

how can i pull the shaft from the lower assembly to replace the impellor?

i am trying to replace the impellor on my boat and just want to know how

done

Yamaha Waverunner Vx110 10 inch long fiberglass pushed in?

i ran into my dock putting a 10inch long hole in not the hull, but above the hull.... How much would this cost to get fixed?

done

1990 mercruiser lower drive?

busted the housing on my lower drive right at the bottom. is there any way to repair without replacing?

done

1986 Evinrude 90hp loss of power, fueling problem?

Hi all, The engine starts and runs well right through the rev range for about 20mins and then looses power and won't rev much over about 2000rpm. I've found if I activate the electric choke by push ... more

done

Motor steering blade?

I ran into an unmarked rock due to low water and took a chunk out of the steering fin, how can I repair it.

done

how to fix my seadoo gtx 1100?

my 2001 seadoo gtx 1100 turns over freely with the spark plugs out but wont with them in, almost like theres too much pressure for the motor to turn over

done

WHERE IS THE THERMOSTAT HOUSING?

I HAVE A 1987 MERCRUISER 470 AND CANNOT FIND THE THERMOSTAT HOUSING..AND MY OTHER QUESTION IS WHERE DOES THE BOAT PICK UP WATER FROM THE OUTDRIVE TO KEEP THE ENGINE COOL..PLEASE IF U HAVE ANY ANSWERS ... more

done

how to paint my mirror boat?

I have a mirror sailing boat but the paint peeling off so i would like to repaint the boat

done

i need wiring diagram for 200hp yamaha outboard 1986?

I need a complete wiring diagram for a 1986 200 hp yamaha outboard. Here are all the numbers that I see, 200ETXJ 6G6 UL 751300 , those are what is on the ID plate.I have spoken with Yamaha 3 times ... more

done

how to fix my sea doo?

my 1996 seadoo REVS WHEN ON TRAILER LIKE IT HAS FULL POWER BUT WHEN I PUT IT IN THE WATER IT JUST WILL IDLE,IF YOU TRY TO GIVE IT GAS IT BOGS DOWN AND SHUTS OFF

done

how di i top up trim tilt fluid?

do i top up trim tilt fluid on my 82 85hp yamaha in up or down positiobn with manual screw on or off any help

done

my 470 mercruiser keeps getting hot?

I tried to take the front cover off but do I have to pull the harmonic balancer off?There is play in what appears to be the water pump impellar!Could this be my problem and what exactly do I have to r ... more

done

Absolute beginner wants to fix a dent/hole in a mirror dinghy?

I have access to a Mirror that was thrown by the wind recently. The first job is to see if I can fix the hull which is dented with a crack of 6 inches or so. All of the wood is there it is just dented ... more

done