my engine overheats and cuts out?

my 2hp marina outboard overheats after about 10mins of running i think it is the impeller but not sure were it is and how to repair it

done

Whats the best way to fix a crack in a yacht keel?

Im considering buying a yacht that has a crack where the keel joins the hull. What is the most effective method of repairing this? The boat is of Ply construction

done

where can i buy spares for a microplus 501 explorer??

hi, i am looking for a rubber or plastic trim for around the deck edge of my microplus explorer but i dont know where to look,could you help me please.

done

my boat sinks?

my boat sinks when it is in water. it is rather embarrising and my girlfriend moans. what can i do?

done

Yanmar YSE 12 inboard diesel will only start if i use easy start please hel?

I have a yanmar YSE 12 inboard diesel engine which for some reason will only start using easy start, i have replaced the injector banjo and that is dry but i have noticed a diesel leak below the pump ... more

done

i'm looking to repair the engine?

Hi, Hope i have picked the right heading, here goes, i have purchased a 20'boat(norman conquer),the engine is a outboard 2cyl, 20 Evinrude,i'm looking for a manual for the engine but don't know whi ... more

done

I live on a boat and want to get on the internet?

I live on a boat and want to run my business of my boat, how do i go about getting an internet connection?

done

how can i fix my keel leak?

i have a 1922 aux ketch rigger from the Dunkirk raids, i have leak along the keel. i know that i can get a sawdust box that i can use to put sawdust underneath the boat it will float up, whereever it ... more

done

how can i tell what size my outboard size my outboard is?

i bought an johnson outboard i was told it was between a 20/25 horse [power and dont know what to put in the fuel tank wether its a mix of petrol and oil or just petrol can i just try it with petrol t ... more

done

were can i get cheap port holes?

were can i get cheap port holes

done

how do i repair a leak i can not see?

i have a trailer sailer wooden one and at the back near the rudder i have a leak i know where it is but it seems to be inside the wood, it there any kind of sealent i can put over the area to fill the ... more

done

How can I seal my clinker boat?

I have a 1950's clinker built sailing dinghy which takes in a lot of water through the hull. As a result I spend most of the time bailing it out! I know it's probably due to it being kept out of the w ... more

done

how can i fix my hull on a microplus 501 explorer?

i have just got a fibreglass microplus explorer,and on the hull there is small crack come hole(about an inch and a quaurter long),i think it has been caused by the support rubber on the trailer its on ... more

done

Ripped seats?

How do I repair the rips and tears in my boat seats?

done

boat not working in forward and revers?

boat was running fine until it kicked out of gear and now forward and reverse not working..any ideas?

done

how to rig a flying jr?

i have a dynamic plastic flying jr sailboat.it is a double bottom model.it was built in 1973.i am looking for all the information i can find out about the boat

done

Kubota workshop manual?

I have a Hydro Marine DM12 engine serial number 121288 fitted in my boat. It is a marinised Kubota 12hp deisel engine that was installed from new in 1978. I would like to obtain a workshop manual that ... more

done

what is the best way to mend a mirror dingy?

How do you make a good repair to a mirror with a hole in it, caused by rot. The holes about the size of a small fist its in the bottom of the boat near the stern, all the rotten wood has been cut bac ... more

done

Mildue on boat seats?

How do you remove mildue from vinal boat seats?

done

how can I fix the scratches, dents and cracks on a 14' fibreglass hull?

I have just purchased an old Lark sailing dinghy. The hull is a little battered and needs some minor and cosmetic repairs. The small deck shows fading. I am looking to repair dents and scratches and a ... more

done