Where can I get a Drive Pinion Assy for my A701A Kenwood Mixer?

Where can I get a new Drive Pinion Assy. for my Kenwood Chef mixer Model A701A.

done

Kenwood Chef - speed knob - how do I get it off?

I am trying to replace the motor in my (very old) Kenwood Chef with a motor from another (even older) Kenwood Chef. This is my first time trying. I am trying to get the motor out of the old Kenwoo ... more

done

kenwood chef model a701a mixer?

My mixer only works on one speed.The control knob does turns as normal but to no avail.

KM200 circuit diagram?

I'm looking for a circuit diagraqm for a speed controller for a Kenwood Chef model KM200.

Burning smell?

Hi I have had this Kenwood chef forever. I did have the gears replaced once and now on using for a few minutes, I get an electrical burning smell. I can use for short periods at a time but if used for ... more

done

How can I remove the K beater from my Kenwood Chef?

I have a 2 year old Kenwood Chef Titanium. The beater is stuck in place and I can't get it out. I am told it is a common problem can someone please give advice?

how can I fix my kenwood chef?

My Kenwood chef is a 1990s model .it has stopped Plug seems ok . I fear a new moor is needed.Any advice I live Watfor herts uk

Repair Kenwood Chef?

I have owned a Kenwood Chef since 1966. It is an Amazing machine. However, the speed on/off/speed dial has ceased to work. Are you able to fix it for me. Please answer asap. Thank you so much. Kathy R ... more

PM900 cuts out?

My kenwood chef pro PM900 keeps cutting out at low speeds. When I use it for pizza dough or something where it has to work hard it goes at high speeds but when I lower it to 2-3 it cuts out. Has any ... more

kenwood chef A901 ?

have replaced all capacitors, resistors and triac but still not working, what else could fault be?

done

how can I fix my kenwood chef pm900 mixer?

Mixer only runs if you hold in green start button, stops if you let go. Fitted new switch panel still same prob what can cause this to happen.

done

My Kenwood Chef 901 works but gives out a hot burning smell?

My Kenwood Chef 901 works but gives out a hot burning smell. I have had it since the 70s with no problems. I have not taken it apart yet but wanted some guidance please

done

How to strip down a kenwood chef?

I need to strip down my kenwood chef a701a to inspect/refit the gears

How do I get the top cover off the Kenwood Chef 901A?

I am following the notes given by "kickstart" in December 2011 for dismantling the motor from our Kewood 901A and still can't get the plastic top cover off! The back has been released by removing the ... more

done

How do I remove the top cover on my old a701a kenwood chef ?

I have got so far but cannot remove the cover at the front where the plastic handle is can you help GED in swinton.

done

How to adjust the speed controller on Kenwood Chef A901B mixer?

Can some one please advise me on adjusting the speed controller on KENWOOD CHEF A901B Mixer. I tried to set it by turning the 2 screws on the side of the control board but it seems to be the wrong way ... more

done

how can i replace the small pulley on a kenwood chef 901?

the small pulley needs replacing on my 1978 kenwood chef 901. i have tried but cant seem to see how to access it without coming at it from below (i.e. removing the motor) as the top (metal) cover is ... more

How do I fix Kenwood Chef Titanium K001 speed problem?

Machine is stuck on highest speed setting, how do I fix, any suggestions please ?

What is the wattage of the 220 ohms 5% resistor on a kenwood chef 901 mixer?

What is the wattage of the 220 ohms 5% resistor on a kenwood chef 901 mixer

C pin on the speed dial Kenwood Che4f A701A?

Can you advise me if there should be a C pin on the speed dial of the Kenwood Chef A701A my machine wont go on slow speed at all only high speed, when I look on the inside from underneath it does look ... more