KMXC560 how to replace small pully & tension bar?

I have to replace the small pully and tension pin on my Kenwood Chef KMC560 I tried to use the liquidiser when not fully engaged. I stupidly tried to force the liquidiser into place before turning the ... more

im trying to fix a kenwood chef mixer a703c ,motor goes gearbox seems to wo?

i have the kenwood a703c the dog clutch doesnt seem to wind right down on top of the large plastic gear .

done

kenwood chef A701 kitchen mixer?

Motor runs OK speed control works OK, until the motor is put under increased load and it cannot cope, checked motor brushes and they are good and long. Any idea please

done

what to clean gearbox of mixer with?

have a Kenwood chef a901e mixer and I am replacing broken gears. I need to clean housing can I use petrol to do this?

done

How do I remove the white plastic cover on my K C a901 ?

The white plastic cover on my Kenwood Chef a901 will not release at the black nameplate end, so I can't get the cover off. What is holding it?

I need a pinion drive gear complet with clutch dog nut?

I have Kenwood chef model A701A it is not working because driving pinion dog nut thread are gone. I want to buy and repair it.

done

kenwood chef dial turning around continuously?

My Kenwood Chef (KM201) won't start. It's not a motor problem but rather seems that the on/off/speed dial, is broken somewhere, as it rotates around and around and doesn't have a stop anymore. How ... more

How can I fix my Kenwood "Chef Excel" (electronic) KM210 Ser No. 0389684 ?

I have noticed a small amount of oil at the rear of the mixer. Not knowing what to expect as yet I have not attempted to dismantle to investigate further. Any thoughts as to what the trouble maybe a ... more

kenwood chef a901?

hi,my speed dial cam fell out and I am struggling to put it back.It won't engage the on off switch so i'm not sure if something has slipped inside the machine.Help appreciated.Carl

How do I find a replacement part for Kenwood Chef MK201?

The on/off and speed control switch went very difficult to turn and then broke off. I have tried to find a replacement without any luck. Help!!! It is quite an old model but was still in gwo until t ... more

Kenwood Chef A701A?

Is there a service manual available? Roger was writing one in June 2013. Is that available please?

implements wont snap in place?

Hello..and thank you for answering my question...I have a very old Kenwood Chef model #A701A (circa 1960's) mixer...the bread hook, paddle and whisk attachments do not lock into place as I suspect the ... more

how to remove supply cable from kenwood chef major?

how do I remove the supply cable from the kenwood chef major. where the cable enters the rear of the mixer the plastic cover has come away and exposed the covered wires .

done

Kenwood Chef A701A Liquidiser Coupling?

Purchased 1975. Liquidiser derives power from plastic 4-pointed coupler on the mixer top. Coupler is normally covered by plastic cover removed for attaching liquidiser. The 4-pointed coupler is worn ... more

How can I fix my Kenwood Chef KM200?

Oil drips into the bowl but otherwise it works well. What is wrong ? How do I fix it?

Kenwood Chef A702 Speed Adjustment?

I have a Kenwood A702 whiich is in food working order but seems a little fast on the minimum speed. Is there a way to "trim" back the speed a little?

wiring circuit diagram for kenwood chef model A901?

Where can I get a wiring circuit diagram for kenwood chef model A901?

My kenwood chef a901 runs at one speed, how can I get multispeed?

My kenwood chef a901 runs at full speed only now I have replaced the two capacitors and two resisters.

Can I buy parts for Chef A.701A?

My Kenwood Chef has broken the middle cog (Britannia metal) big teeth on the bottom plate with smaller teeth on the upper part. It's between the front and rear cogs. The liquidiser drive still works ... more

done

Service manual for Kenwood Chef?

Does anyone know where I can get or download a service manual for a Kenwood Chef Major A707A?