lawn mower?

How do I change the pull cord on my lawn mower?

done

how do I test the coil, distributor and points on an engine?

I have an old international 6 cyl tractor motor on a wood chipper. It has no spark, and the distributor is turning. The cap, rotor, and points look good, no arc tracking on cap or burrs on points. C ... more

done

Where to posistion new blades on Craftsman 3 blade mover?

My mower leaves an uncut patch of grass about 6 inches wide about in the middle of the cut path. I have replaced all three blades and it did not help. Do the blades need to be installed in a set patt ... more

done

What is the timing settings for a Mountfield Engine?

I have a mountfield engine of a lawnmower and it is has been given to me in bits. The con rod in the engine is snapped. I can manufacturer a new one but need a workshop manual to reassemble and set ti ... more

done

Leveling the mower deck on a Craftsman?

Any suggestions on how to level the mower deck on a Craftsman 42 inch cut lawn tractor to stop uneven cut? I changed blades and now it cuts a deep grove on one side.

done

My riding lawn mower engine dies?

MY 1997 poulan (mfg#HD145H42)(MODEL#733-864)riding lawnmower dies when I engaged the blade. How can i fix it?

done

How can I get my lawn mower started?

My father' s Sears Craftsman 5.0 HP, 4-cycle, self propelled mulching mower sat for seven years after he died. It ran fine then. I retrieved the mower, changed the plug, replaced oil, new gas, took a ... more

done

lawn tractor will not move?

Our sears lawn tractor mower Craftsman 310707 type 0137-51 will not move forward or backward. Starts fine. When I put it in gear it does nothing. Doesn't make any sound when I put it in gear. Coul ... more

done

My mcculloch petrol strimmers start pull cord stays out when I pull it?

I have a Mcculloch grass strimmer and when I try to start it the pull cord stays out how do I mend it

done

how do you adjust a clutch on a 8 hp snapper disc drive 5 speed ?

i have an 8hp snapper-disc drive-5 speed riding mower that will go in reverse but doesnt want to go foward . how do i adjust the clutch on this mower?

done

How can I fix my Briggs & Statton mower blade w/o buying a new one?

How can I fix my lawn mowers blade without having to buy a new one? I mean the blade is still in one whole piece and still connected to the lawn mower. It's just that I hit a stump that was really l ... more

done

Where can I find a Westwood Lawn tractor workshop manual?

I have a westwood 1600H35 lawn tractor that has recently been serviced and will now not start having run just once for 6 hours. I have changed the battery (45 Ah) and attempting to clean all the cont ... more

done

How do I adjust the blade height on my push lawn mower??

??

done

How do i fix a front wobbling tire on my riding mower?

How do i fix a front wobbling tire on my riding mower?

done

how do I sharpen my black and decker hedge trimmers?

would like to sharpen blades on hedge trimmers, about ten years old

done

Engine starts fine,run great, but dies when clutch is released?

14hp Snapper 38" riding mower.,, Dog ate some wiring ( right side)but couldn't find any broken wires. Ground wire to starter pulled out but I fixed that. Where can I get a wiring diagram or advice??? ... more

done

how do i get my blade to turn on my murry?

on a two blade murry one side turns fine the other side turns for a minute and then binds up.igot a rope tangled in the one side,i've changed the blade but it still binds.

done

battery?

i have a craftsman 10 hp rider it runs good but you have to jump start it every time i tried a new battery and it drained it what could be the problem

done

How do I install the drive belt on my sears hp magnum garden tractor?

I have an older model sears garden tractor with a 20 horsepower Kohler motor. The drive belt came off and although I have a new belt I need to know how to install it.....where the tension release poin ... more

done

garden tools, lawn mowers?

how do i fix my flymo r32 that wont cut properly and is making a ratling noise

done