GBC Ultima 65 Doesn't heat up?

We've replaced the coils and the circuit breaker. Finally checked for power. We have current going into the board (AC-in) but nothing coming out (Heater). Do we need to replace the whole board? Th ... more

done

Ultima 65 over heating?

Ultima 65 ready light never shows ready, it continues to blink, but the laminator is getting very hot, too hot to use.

done

I want to lower the temp on my laminator 4250?

I am using lam 2 film which is low temp film and my 4250 get too hot and starts to melt the film in place on the roll. My 4250 shows that it is ready to use when the amber flashing light goes to the g ... more

done

How to fix an overheating TSL-2700 Laminator?

How do I fix a TSL-2700 Laminator with an Upper Heat Roller that is overheating?

done

Ultima 65 Can't get poles off?

We cannot get the poles off that hold the laminating paper. It says to move it to the right and then pull out of the left side. This doesn't work for us, the pole will not release. Any help?

done

GBC Ultima 65 ready light not turning on?

Hi, Our GBC Ultima 65 laminator stays on wait light continually. The ready light will not come on, however it will still laminate and the other functions seem to work. Whats wrong with it? Thank ... more

done

ultima65 laminator no heat?

The unit powers on but heat light does not go on and ready light on. Runs forward and backward but no heat. Interlocks all good

done

How can I fix my 4250 laminator?

Everything on the machine is practically new & works beautifully...then today it won't heat! Light flashes WAIT but never gets hot! What's the prob?!?! I live in TX! Please help...I operate a smal ... more

done

How can I fix Fellows Home Laminator MarsA4?

My Fellowes Home Lamiator MarsA4 Jammed opened removed 2 screws on top then 4 plastic round pieces underneath screws beneath came apart and removed jammed item put together but now when used item ... more

done

GBC Ultima 65 Laminator?

Laminator runs fine for about 2-3 feet of lamination, then just stops-power is on, heat is on, rollers just stop. When the machine is turned off for a few minutes and cools some then the rollers will ... more

done

how can i fix my fellowes laminator?

My laminator is showing standby light only so how can i fix it so that it can show green light

Heat roller Ultima 65 Bob Haller you out there???

Bob I have another Ultima 65 that has a heat roller swollen in the middle. (apparently My name is getting around this school district). Any suggestions for getting the roller(s) at a reasonable price. ... more

done

GBC Pinnacle 27 laminator top film roll not moving?

We jus installed this laminator today. I have loaded the top and bottom film roll and made sure the feed tray was locked in place. The bottom roll feeds fine but the top roll will not move/roll. He ... more

done

Ultima 65 Laminator. I put 27" film and now can't get it out?

I put the 27" film on the rod and it was hard to get into the machine. Now I can't get it out.

done

Lost power while running and will not power back on, help!?

GBC-4250 - Lost power while running and will not turn back on. I tried a new power strip and replacing the fuse but it still does not turn on. What else should I try? Are the motors replaceable?

done

GBC Ultima 65 problem?

GBC Ultima 65 I repair these, but I don't see too many I only know of 3 in Dublin, however I have one that's stopping cooling and starting I took off the covers and ran without the chain, the motor se ... more

done

J-H Card/Guard 6200?

Can anyone tell me how to get the rollers out to clean them? I found instructions for a similar model but the way the rollers lift out of the housing is different

How can I fix my Gbc Laminator?

I have A GBC Ultiam 65 laminator it is getting to hot. It has no temp control knob. Could it be the main board.

done

Pouch stuck in Fellowes Mars A4 laminator?

An a4 pouch has become stuck inside the laminator and i am unable to get it out as not visible. Only 2 screws underneath which don't seem to undo anything. Any ideas to be able to undo cover if possib ... more

How can I fix my Rexel LV250HS - no power light?

Hi, I need to fix a Rexel LV250HS laminator. Rollers are moving but there is no Red power light showing or heating happening. Any help gratefully appreciated.