Wrinkles?

My EasyLam II is producing wrinkles when I laminate. I recently changed rolls and since, it doesn't laminate correctly. Any suggestions?

help?

hi im a custodian at a elementery school im new to this site. these teachers have been with a laminator for about 2 years. so i dusted it off and looked into it.it works fine for about five min then i ... more

How Can I Fix a GBC 620 0S,2013?

The switch for the machine that varies the length and temperature will only work forwards. What could be causing this? A faulty switch or control board?

done

How can I unblock my proaction paper Shredder?

I put a membership card into the Shredder as my Shredder was supposedly able to shred credit cards. Now it won't budge either way . How can. I unlbock it?

done

wison jones LP25HS Laminator?

won't power on. I used last week without incident. turned off afterwards. went to use this morning and it won't power up at all. any suggestions or is it just trash?

How do I fix the tension on the pull rollers motor's chain?

We checked the front red rollers and they move freely. We took off the cover and observed the chain from the motor driving the pull rollers. It tightens till it's too tight and then there's a loud cl ... more

Why will the back rubber rollers on the Minikote 18 inch not turn?

the machine will heat and adhere the laminate but will not pull through the rubber rollers to finish the product.

How can I stop GBC Ultima 65 from overheating?

How can I stop GBC Ultima 65 from overheating? It doesn't want to maintain proper heat range.

Why will my pinnacle 27 Laminator work?

The power switch on my Pinnacle 27 Laminator lights up, however it does not work! What may be the problem?

fellows a3 voyager?

I have a big tear in the top silicone roller. can I buy a replacement from anywhere or how much would it cost to be fixed.

Ultims 65 speed control?

We can put it at its lowest running speed and it will still run at the starting speed. it wont slow down at all. Thanks

New machine or repairable?

My school's Minikote G3 laminator was left on too high and was turned off when found. Now, it will not heat at all. Does this sound like something that is repairable or is it possibly fried and done ... more

done

GBC Ultima 65 rollers just arollin' nonstop?

Help. I have a GBC Ultima 65 which turns on, but the rollers immediatly run. The control panel seems ok, i looked at it and cleaned it. The roller heats, and green light comes on when ready. The r ... more

done

GBC Docuseal95 heats up but rollers wont turn?

I have a GBC95 which heats up quick but wont feed the the pouch . The rollers don't seem to be turning. Any suggestions? Thanks.

done

parts for tsl-2700?

Where can I get parts for tsl-2700 laminator and tcc-2700 laminator

Why does the GBC Pinnacle 27 on/off switch not work?

GBC Pinnacle 27 on/off switch does not work (machine will not go on). Any service reps in Wisconsin?

done

Our GBC laminator ultima 65 heats but does not roll forward? Suggestions?

Our laminator heats up but will not engage and roll forward to feed laminator film through. Any suggestions?

How to fix my laminator, never used but just beeps at me?

Hello I got this laminator Voyager A3 High-Performance Office Laminator by Fellowes. Had it sitting on a filing cabinet since 2011 unused, never even plugged in, as it was given to me and not need ... more

laminator is not heating up?

I have GBC Ultima 65 laminator, all appears to be working fine except heat light is blinking all the time and Am Not getting any Heat on rollers? What do I need to do to get heat to come on? I bough ... more

how to fix GBC Ultima 65 roller that won't heat up?

The top roller of our GBC Ultima 65 heats up but not the bottom roller. What might be wrong and how do I fix it.

done