GBC Lamiator stopped working?

I have a GBC Ultima Laminator and during a big job, it just stopped working, light are not on, I have tried changing outlets and checking our schools breaker box. The laminator is just dead in the wa ... more

Laminator gbc ultima 65 How to reinstall a power switch?

I had a wire burn out to the power switch and it burned a post off the switch. I have purchased a new switch and I need to know how to re wire it. GBE ultima 65 laminator.

done

How Can I Fix a GBC 620 0S,2013?

The switch for the machine that varies the length and temperature will only work forwards. What could be causing this? A faulty switch or control board?

done

How can I stop GBC Ultima 65 from overheating?

How can I stop GBC Ultima 65 from overheating? It doesn't want to maintain proper heat range.

GBC Ultima 65 rollers just arollin' nonstop?

Help. I have a GBC Ultima 65 which turns on, but the rollers immediatly run. The control panel seems ok, i looked at it and cleaned it. The roller heats, and green light comes on when ready. The r ... more

done

GBC Docuseal95 heats up but rollers wont turn?

I have a GBC95 which heats up quick but wont feed the the pouch . The rollers don't seem to be turning. Any suggestions? Thanks.

done

Why does the GBC Pinnacle 27 on/off switch not work?

GBC Pinnacle 27 on/off switch does not work (machine will not go on). Any service reps in Wisconsin?

done

Our GBC laminator ultima 65 heats but does not roll forward? Suggestions?

Our laminator heats up but will not engage and roll forward to feed laminator film through. Any suggestions?

laminator is not heating up?

I have GBC Ultima 65 laminator, all appears to be working fine except heat light is blinking all the time and Am Not getting any Heat on rollers? What do I need to do to get heat to come on? I bough ... more

how to fix GBC Ultima 65 roller that won't heat up?

The top roller of our GBC Ultima 65 heats up but not the bottom roller. What might be wrong and how do I fix it.

done

How can I tighten film tension?

I have a GBC 173LM. The film tension is very loose. How can the film tension be adjusted.

GBC Ultima 65 Breaker?

I've got an Ultima 65 that trips its breaker every once in a while. It's not frequent (once every 3 months or so), but I was wondering what causes that and should I be concerned?

done

GBC Catena 65 is getting too hot?

GBC Catena 65 is getting too hot. Not a lot, but enough to wrinkle/wavy/orange peel the lamination. The temp is set at 230 for 5 mil, but if I check it when it's running a while or if I've let it set ... more

Heat light continues to flash on my GBC Ultima 65 even though it is ready?

The heat light continues to flash on my laminator even though it says it's ready. Why is that?

done

GBC 4250 No Power?

What happened: Co-worker went to use the rear cutting blade to cut off excess laminate while the machine was in operation (rolling). I happened to be overseeing the project and watched as the unit si ... more

done

GBC Ultima 65 Smells Hot, Like It's Burning?

I've Cleaned the Residue From the Ends of the Heat Rollers and Users Say It Still Smells. They have theorized that the heating elements are bad. Is it possible they are too hot? Is the temperature ... more

done

our GBC Ultima 65 control panel is not on?

Our GBC Ultima 65 control panel is not on. The laminate frolled into the heat rollers and the control panel shut off and is not on at all.

done

How can I fix my GBC Ultimate 65-Top roller falls out while laminating?

While laminating my top roller will pop out and fall. I believe one end is a little tighter then the other, is this possible? How would I correct a problem like this?

done

GBC laminator rollers will not turn?

Fuse went out, replaced it, everything turns on heats up, but the rollers do not roll.

done

GBC Ultima 65 Power Switch Failure?

The AC Switch on my Ultima 65 burned out/melted. I replaced the switch and that one melted, too. What would be causing this? Could it be caused by corroded leads on the wires plugged into the switc ... more

done