how do i change the access code on my 9448+ scantronic?

I need to change the access code on my 9448+ scantronic alarm but do have any instructions. Can anyone help please.

done

Scantronic 9448+ Reset?

Hi Guys I've looked on this forum at the other threads about resetting the 9448+ and the instructions say to locate the RST Pins and place a screwdriver over them to short..... My question is wher ... more

done

How can I fix my Scantronic 9448 with 9427 panel?

I am after the user manual/ instructions for the Scantronic 9448, the lights and sensors are working but I cannot set the alarm. I guess I need to reset. Had the manual at 1 point and tried by followi ... more

done

Scantronic 9448+ Alarm Sounds on exit?

I have reset my alarm due to replacing an internal fuse - after a bit of searching for the fault! Engineers walk test shows that all the sensors are working correctly but whenever I type the exit cod ... more

done

how can I fix my scantronic 9448+?

power in the local area was turned off for an emergency, when the power returned it has been impossible to turn the alarm off unless at the mains - can you please give advice.

done

Adjust alarm set sound length on Scantronic 9448?

When I set the alarm the length of the sound before it stops is excessive, can and how this be adjusted.

done

where can I buy a scantronic 9448+ style in the Netherlands? ?

where can I buy a scantronic 9448+ style in the Netherlands? ?

done

Control Panel not lit up / Internal alarm has sounding?

Hello, I have recently realised that the control panel on my alarm (Scantronic 9448) is not iluminated anymore then last night the internal alarm sounded. Please help?

Wiring up a Scantronic 9427 Style?

I had to move my keypad, a Scantronic 9427 Style, and didn't make a note of which colour wires from the 9448+ went into the connector on the unit. Can anyone help me please ?

done

Please advise if I can replace just the keypad?

Our Scantronic 9448 is 18 years old, and to the best of my knowledge has never had a new battery. As there is no instruction booklet, can you please advise where the battery goes? The alarm went off ... more

done

where can i get operators instructions?

scantronic 9448+ dont know whatbutt0ns do on front of control panel

done

Cant manage to reset my passcode?

Hi, I have a Scantronic 9448+ approx 10 yrs old. Unfortunately my children flooded the bathroom floor and water was dripping through the light fitting in the kitchen so I powered all the downstairs li ... more

done

Scantronic 9448?

The external alarm went off in the middle of the night, although the alarm was not set. I replaced the battery in the box in my cloakroom but the tamper light remains on and when i type in the reset ... more

done

scantronic 9448+?

i have a 9448+ with 2 remote keypads the alarm is working fine, the only problem is the mains light on the main panel is ok but the mains lights on both keypads are flashing.

Scantronic 9448 3 Zone Alarm?

Hi, I need an installation guide for a Scantronic 9448 3 zone panel. Would appreciate any help.

done

how do i find out?

how do i find out my code for a scantronic 9448+? thanks in advance

done

Connections from Scantronic 9651 to Menvier SD1+ dialer?

Hi, Im upgrading from a Maplin alarm panel to a Scantronic 9651, I also have the Menvier SD1+ dialer. The Panel comes with a pre wired plug at one end but in the Menvier instalation manual it does no ... more

done

How can I set my Scantronic 9448+ alarm?

I have followed instructions from helpful suggestions on this site and have also got copy of installation guide for scantronic 9448+ - but still having problem - when I put user code in to set the ala ... more

done

scantronic 9448 fault?

we have been having powercuts lately and the alarm is about 10 years old i think when the power goes the outside rings and really funny it rings like a school bell not the normal sounder you would hea ... more

done

Scantronic 9448 alarm?

Hi, just looking for some guidance please, a tenant has just moved out of a small flat i own, it has an old scantronic 9448 alarm installed, I've just discovered that the alarm has not been used since ... more

done