alarm don't work?

I've wired it up now but it don't work like it says it should,I've taken some wires out and swapped them but it still rings and rooms 1246 are lit.I hav'nt wired the panic box up yet so i'am sure it's ... more

done

Scantronic 9448+style alarm?

My parents recently had a power cut at home and this seems to have disabled there alarm (scantronic 9448+style) the key pad is illuminated but not working, I have checked all three fuses and these see ... more

done

alarm has went dead?

after a power cut my scantronic 9448+ has packed up i have no lights on the keypad or the main box in the attic,i have checked the fuse board and no trips have been triped.Help.

done

How to shut off a Scantronic 9448+ alarm when there is a power failure?

Our external alarm sounds when a power failure occurs and will not acccept reset codes so the alarm sounds for about 20 minutes which I assume is preset. Drives our neighbours mad. Any solution?

done

Scantronic 9448+?

Hi Just moved house, was unsure of code on my scantronic 9448+ to cut a long story short we tried the code we thought and attempted to reset to a memorable number. The alarms went off and could not s ... more

done

alarm will not let me program?

scantronic 9448 panel brand new replacing old 9448. all wiring the same,one set door contacts,2 pir,s.all unused zones shorted out, only using zones 1,2,and 3, yet it still wont let me program it.h ... more

done

Scantronic 9448 tamper light and pulsing alarm when I enter code?

I have a scantronic 9448 alarm about ten years old. When I enter my code to set my alarm it begins to sound a pulsing alarm and a red tamper light comes on. How do I resolve this?

done

how can i get my scantronic 9448 up & running again?

the alarm got disabled somehow during building work, at the time the alarms all sounded. now we cant get it working. sensors are active.

done

How do I re-set a disabled Scantronic 9448+ alarm?

Electrician had to turn the mains power off to do a job and when he turned the power back on, the alarm sounded. The user code buttons would not work so the electrician punched in 1 2 3 4 to turn the ... more

done

I have a scantronic 9448+ extra zones ?? ?

I have a scantronic 9448+ and have installed extra zones , but these are not coming up on walk test, not sure either if I am in program/engineer mode ? also is it possible to put a chime on the en ... more

gts ?

see below - scantronic 9448 change user code

done

scantronic 9448 change user code?

how do I change my user code on my scantronic9448 alarm panel? Please help me. Thanks.

done

how do you change user code on a scantronic 9448+?

how do you change user code on a scantronic 9448+

done

I have just fitted a new battery to my scantronic 9448 alarm?

How do I reset /get my system to work again

done

scantronic 9448+Stle alarm System?

The control panel dosent show any lights, the fuse is ok. The alarm will not set and no tones emit when buttons are pressed

done

do i need to enter engineers code to dis-connect external bell box and repl?

hello need some advice, have tested bell-box which has a supply present from alarm panel of 12v d.c,the o/s sounder never goes off ,the system is a scantronic 9448+,what is the procedure for changing ... more

done

how can i fix my scantronic 9448+?

i have an intermittent fault on the tamper circuit, a local engineer has checked the system but was unable to find the problem.can the tamper circuit be disconnected but still allow the system to wor ... more

done

How to connect a Defender Bell Box to a Scantronic 9448-90 panel?

Can anyone give me the wiring connections for the above.

done

scantronic 9448+ external sounder not working?

scantronic 9448+ outside bell does not sound when it should, but the sounder in the house does,has the outside sounder got it's own battery or is it fed from main battery?

done

reset code or engineer number re 9448+ style scantronic?

I have a scantronic 9448+ style which I use with the 9427 style keypad. I moved into my house this year and do not have the code. How do I reset? I cannot find any RS molex pins or a reset button? Is ... more

done